Knowledgebase

Sewer line lawn repair #896258

Asked April 03, 2025, 10:22 AM EDT

What is best to use to fill areas in sunken clay yard about 1’ deep at corner of house foundation (damage from sewer line digging)? See photo.

Ramsey County Minnesota

Expert Response

Thank you for your question! 

To properly fill in a sunken area, it’s best to use a layered approach. This helps ensure good drainage, long-term stability, and prevents future settling.

Start by clearing the area of any debris and breaking up compacted soil. If needed, dig out the sunken section to prepare for proper backfilling. For subsurface drainage measures, as recommended by this Iowa State University Extension guide (Building Basements in Wet Locations), begin by adding a layer of 1/2- to 1-inch pea rock at the bottom, filling up to about 18 inches below the surface to improve drainage and provide a stable base. Then fill the remaining depth with soil that matches the existing yard, ideally blending in clay and topsoil to create a low-permeability layer that helps prevent surface water infiltration. Avoid placing gravel or stone near the surface, as these materials can allow water to enter the ground too quickly. 

For the final 3-6 inches, top it off with screened topsoil or sandy loam to support plant growth and promote surface drainage. Make sure to grade the area so that it gently slopes away from the foundation (ideally 1 inch per foot for at least 6 feet), as recommended by the University of Minnesota Extension. This slope helps direct water away from your home and protects your basement from moisture issues. Moisture in basements: causes and solutions

Make sure to clear out debris and loose chunks as you go, then compact each layer. You can use a hand tamper for this. Once your fill and grading are done, consider planting natives on that site to prevent erosion in the future.

Please reply to this message with any further questions.

Best,

Victoria

University of Minnesota Extension Master Gardener

An Ask Extension Expert Replied April 07, 2025, 11:48 AM EDT

Thank you for your question!

To properly fill in a sunken area, it’s best to use a layered approach. This helps ensure good drainage, long-term stability, and prevents future settling.

Start by clearing the area of any debris and breaking up compacted soil. If needed, dig out the sunken section to prepare for proper backfilling. For subsurface drainage measures, as recommended by this Iowa State University Extension guide (Building Basements in Wet Locations), begin by adding a layer of 1/2- to 1-inch pea rock at the bottom, filling up to about 18 inches below the surface to improve drainage and provide a stable base. Then fill the remaining depth with soil that matches the existing yard, ideally blending in clay and topsoil to create a low-permeability layer that helps prevent surface water infiltration. Avoid placing gravel or stone near the surface, as these materials can allow water to enter the ground too quickly.

For the final 3-6 inches, top it off with screened topsoil or sandy loam to support plant growth and promote surface drainage. Make sure to grade the area so that it gently slopes away from the foundation (ideally 1 inch per foot for at least 6 feet), as recommended by the University of Minnesota Extension. This slope helps direct water away from your home and protects your basement from moisture issues. Moisture in basements: causes and solutions

Make sure to clear out debris and loose chunks as you go, then compact each layer. You can use a hand tamper for this. Once your fill and grading are done, consider planting natives on that site to prevent erosion in the future.

Please reply to this message with any further questions.

Best,

Victoria

University of Minnesota Extension Master Gardener

An Ask Extension Expert Replied April 09, 2025, 1:54 PM EDT

Thank you for your question!

To properly fill in a sunken area, it’s best to use a layered approach. This helps ensure good drainage, long-term stability, and prevents future settling.

Start by clearing the area of any debris and breaking up compacted soil. If needed, dig out the sunken section to prepare for proper backfilling. For subsurface drainage measures, as recommended by this Iowa State University Extension guide (Building Basements in Wet Locations), begin by adding a layer of 1/2- to 1-inch pea rock at the bottom, filling up to about 18 inches below the surface to improve drainage and provide a stable base. Then fill the remaining depth with soil that matches the existing yard, ideally blending in clay and topsoil to create a low-permeability layer that helps prevent surface water infiltration. Avoid placing gravel or stone near the surface, as these materials can allow water to enter the ground too quickly.

For the final 3-6 inches, top it off with screened topsoil or sandy loam to support plant growth and promote surface drainage. Make sure to grade the area so that it gently slopes away from the foundation (ideally 1 inch per foot for at least 6 feet), as recommended by the University of Minnesota Extension. This slope helps direct water away from your home and protects your basement from moisture issues. Moisture in basements: causes and solutions

Make sure to clear out debris and loose chunks as you go, then compact each layer. You can use a hand tamper for this. Once your fill and grading are done, consider planting natives on that site to prevent erosion in the future.

Please reply to this message with any further questions.

Best,

Victoria

University of Minnesota Extension Master Gardener

An Ask Extension Expert Replied April 09, 2025, 1:54 PM EDT

Loading ...